LeCroy — A — User Manual ADCs and Memories 4 Trigger 4 Automatic Calibration 5 Display 5 Manual/Remote Control 5 Specifications. LeCroy Service Manual. Identifier LeCroy__Service_Manual. Identifier -ark ark://t47q2vs Ocr ABBYY FineReader A DIGITAL OSCILLOSCOPE SERVICE MANUAL North American Headquarters: LeCROY Corporation Chestnut Ridge Road Chestnut Ridge, NY.
| Author: | Tejin Vukus |
| Country: | Chad |
| Language: | English (Spanish) |
| Genre: | Technology |
| Published (Last): | 8 April 2014 |
| Pages: | 139 |
| PDF File Size: | 3.91 Mb |
| ePub File Size: | 8.31 Mb |
| ISBN: | 757-4-46819-259-4 |
| Downloads: | 66399 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Tokazahn |
Calibration Error Log Scan by Paladinmicro – paladin paladinmicro.
Stop electronic waste – fix it yourself
How reliable is it? Digital lecdoy appears to have measured voltages lower than expected. Plotting is done in parallel with normal Oscilloscope operation. The four branches numbered 4, 1, 2 and 3 starting from the top of the board are Mhz clocked with a delay of 2.
Arithmetical and mathe- matical functions can also be chained together to construct more complex processing routines. X3 display cord connector: Insert or lecrly the PAL into location A Expansion shows side bands at 10 Hz and I have an operators manual, but a Service manual Lecroy part number SMA would greatly facilitate the repair process.
Adjust the size of the display, in order to get 5mm gap between the middle of mnaual image lines top, bottom, left, lecro and the CRT lines. Lithium batteries maintain front-panel settings and waveform data for 2 years. The result is shown in the middle trace complete with cur- sor readout. Preliminary The source checks for presence of listeners and places the next data byte on the data lines DI In addition, there are 8 ground lines, making a total of 24 lines.
Long non-volatile memories-Two non-volatile 50K acquisition memories, one per channel, store signals. Scan by Paladinmicro – paladtn paladinmicro.
LeCroy 9450 Service Manual
This mode is realized by turning the beam spot ON or OFF according to a downloaded bit mask while moving the spot in the x-direction. With both Channel 1 and Channel 2 inputs open, set the DS0 as follows: Comments 0 No comments yet. The error status is represented in a hexadecimal number, for each acquisition condition. These terms and conditions contain rules about posting comments.
Other trigger features in- clude hold-off by time or number of events lecro, gated triggering and conditional triggering, qualified trigger, and trigger delayed by time or number of events.
The second and third oscillations are now clearly visible. Before connecting a plotter to a DSO, do not forget to select the appropriate settings in the plotter menu and the RS menu pages.
To change the fine gain potentiometers remove the by removing the four screws and washers. Set the time base: Selection of the transform size: Box Meyrin 1 – Geneva, Switzerland Telephone: Maximum number of devices 15 Maximum bus length 20 meters or 2 meters per device, whichever is less Connection star or chain Scan by Valadinmicro – lecdoy paladinmicro.
Tektronix PS or equivalent. This is the fastest lecoy This option is used for lower timebase setting. The instrument features high-fidelity 8-bit ADCs, 50K of non-volatile acquisition memory per channel, K of additional waveform storage memory, extensive pulse parameter analysis, and a highly sophisticated trigger system to capture the most complex signals, including spikes and glitches.
Service manual of Lecroy A DSO
The following hard-copy parameters are required on the A: Lefroy this way the envelope of all waveforms is accumulated for up to a maximum of 1 , sweeps. These arithmetic functions can be performed on any source waveform on a point by point basis.
Fully Featured with Remote Control- All the front-panel commands used to drive the memory card system are available through re- mote control. LeCroy Sari 01 Germany: IK RES05 1 90 3. The gate array has read-only memory access.